CPU Heatspreader Lapping

Mike SchroppComputers 5599 Comments

I’ve been busy as of late trying to optimize my current system for Grid computing. This means 24/7 operation at 100% CPU and GPU load. My system was previously overclocked and setup without any real purpose other than better productivity and daily usage. I had not really pushed it that hard and had a somewhat mild overclock.

With the recent change towards optimizing my setup for Grid Computing I decided to push my overclock a little harder. On top of that, I also plan on leaving my computer running 24/7. These two things mean I needed to re-evaluate my cooling setup to ensure that I would be able to keep my temps in check.

My current computer setup is a AMD x4 940BE processor with a XIGMATEK HDT-S1283 cooler. The case is an Antec 900 with the stock Antec fans swapped out and replaced with higher flowing Silverstone fans. My previously CPU overclock around 3.4Ghz. I never really tinkered too much with it much before. I have another rig that has a 4.0Ghz Intel C2D that was my primary overclocking toy.

I decided to push my AMD setup closer to 3.8 Ghz since I knew that would help a little with my points per day production for Grid Computing. This required a bit of a voltage bump and subsequently a little more heat. After loading up Prime95 and doing some stressing I found that my temps were running around 50-51c. Not bad, but something I thought I could improve upon. I decided the easiest way would be to lap the heat spreader on the CPU (which I’ve done in the past) and found it to be worth a couple of degrees.

Since I was going to be lapping the CPU heatspreader I figured I would take the opportunity to measure the surface finish as well before and after. The main purpose of lapping the CPU heatspreader is to make sure the surface is perfectly flat so that there is maximum contact with the CPU heatsink base. More contact equals better heat transfer. The surface finish is a secondary thing, and while I don’t believe it has anywhere near as much impact as the flatness, I do think there is some value in the finish. Using a profilometer I was able to measure the RA finish of the CPU heatspreader before and after lapping.

Starting with 600 grit sandpaper and working in steps (800 grit, 1200 grit, 1600 grit) and the finishing it off with a light touch of 2000 grit yielded some pretty good results. During the lapping process I found that the stock CPU heatspreader was not all that flat. While the stock CPU heatspreader looks flat to the naked eye, it’s pretty obvious after you start lapping that it is not.

Stock CPU-

AMD Phenom II CPU Heatspreader

CPU Stock

After lapping for a couple of minutes here is what you end up with.

Processor Heatspreader Lapping

CPU Heatspreader Initial Sanding

Here are my surface finish measurements before and after lapping. (RA finish in inches)

Stock12 RA
Fully Lapped3.1 RA

Again, I’m not sure how much the RA finish comes into play but as you can see the improvements are pretty good from lapping.

Finished CPU after lapping-

Lapped Processor Heatspreader

Finished CPU Heatspreader

Now for the numbers that matter most; the temps. Here are the results of my 6 hour stress tests using Prime95 and maxing all 4 cores out at 100%.

Stock CPU51.3c (Peak Temp)
Lapped CPU47.2c (Peak Temp)
Difference4.1c

All in all the lapping process returned some excellent results. I managed to drop my temps another 4c.  The temps I had before were not that bad but they were a little high for my liking. Being able to reduce my temps further makes me feel better about operating my computer 24/7. Plus I was able to up my overclock another 400Mhz on top of that .

Facebook29.2k
Twitter13.2k
Pinterest7.1k
Pinterest
Pinterest
LinkedIn2.1k
RSS813
Follow by Email2.6k

Comments 5,599

  1. エロ い コスプレName _____________________________Address _____________________________——————————————————————————————————422The Boys’ Magazineis unquestionably the finest magazine in the world for boys.Eachissue is filled with fascinating stories and absorbing articles all ofintense interest to every live boy.

  2. I’m not that much of a online reader to be honest but your sites really nice,
    keep it up! I’ll go ahead and bookmark your website
    to come back in the future. Cheers

  3. Definitely consider that which you said. Your favourite justification seemed
    to be on the internet the simplest thing to take into account of.

    I say to you, I definitely get annoyed whilst people consider issues that they just do not realize about.
    You managed to hit the nail upon the highest and also outlined out the
    whole thing with no need side effect , people could take
    a signal. Will likely be again to get more. Thank you

  4. Howdy this is kinda of off topic but I was wanting to know if blogs use
    WYSIWYG editors or if you have to manually code with HTML.
    I’m starting a blog soon but have no coding expertise so I
    wanted to get guidance from someone with experience. Any help would be enormously appreciated!

  5. Write more, thats all I have to say. Literally, it seems as though you relied on the
    video to make your point. You clearly know what youre talking about, why throw away your intelligence on just posting videos to your blog
    when you could be giving us something informative to
    read?

  6. Simply desire to say your article is as astonishing.
    The clarity for your publish is just great and that i could assume
    you are an expert on this subject. Well with your permission allow me to snatch your feed to stay updated with
    forthcoming post. Thanks a million and please keep up the rewarding work.

  7. Hi, I do believe this is an excellent website. I stumbledupon it 😉 I may
    return yet again since i have book-marked it.
    Money and freedom is the greatest way to
    change, may you be rich and continue to guide other
    people.

  8. Nice weblog here! Additionally your website a lot
    up fast! What host are you the use of? Can I get your affiliate hyperlink in your host?
    I want my website loaded up as fast as yours lol

  9. her sole consolation was limited to the prospect of depositingher sorrows in the grave; and her only wish was to procure a retreat inwhich she might wait with resignation for that happy period.ラブドール 無 修正Yet thismelancholy comfort she could not obtain without the advice andmediation of whom she therefore still continued to see andconsult.

  10. “I may perhaps not see you again.エロ フィギュア 無 修正..”“Are you… going away?”“I don’t k.. to-morrow….”“Then you are not coming to Katerina Ivanovna to-morrow?” Sonia’s voiceshook.“I don’t k I shall know to-morrow morning…. Never mind that: I’vecome to say one word….”He raised his brooding eyes to her and suddenly noticed that he wassitting down while she was all the while standing before him.“Why are you standing? Sit down,

  11. Hi there, just became aware of your blog through Google, and found that it’s really informative.

    I am gonna watch out for brussels. I will be grateful if you continue this in future.
    Numerous people will be benefited from your writing.

    Cheers!

  12. Wow that was strange. I just wrote an incredibly long comment
    but after I clicked submit my comment didn’t show up.
    Grrrr… well I’m not writing all that over again. Regardless, just
    wanted to say wonderful blog!

Leave a Reply

Your email address will not be published. Required fields are marked *